View LT19331_4825740.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

FEATURES
n n n n n n n n n n n n
LT1933 600mA, 500kHz Step-Down Switching Regulator in SOT23 and DFN Packages DESCRIPTION
The LT (R)1933 is a current mode PWM step-down DC/DC converter with an internal 0.75A power switch, packaged in a tiny 6-lead SOT-23. The wide input range of 3.6V to 36V makes the LT1933 suitable for regulating power from a wide variety of sources, including unregulated wall transformers, 24V industrial supplies and automotive batteries. Its high operating frequency allows the use of tiny, low cost inductors and ceramic capacitors, resulting in low, predictable output ripple. Cycle-by-cycle current limit provides protection against shorted outputs, and soft-start eliminates input current surge during start up. The low current (<2A) shutdown provides output disconnect, enabling easy power management in battery-powered systems.
L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners.
Wide Input Range: 3.6V to 36V 5V at 600mA from 16V to 36V Input 3.3V at 600mA from 12V to 36V Input 5V at 500mA from 6.3V to 36V Input 3.3V at 500mA from 4.5V to 36V Input Fixed Frequency 500kHz Operation Uses Tiny Capacitors and Inductors Soft-Start Internally Compensated Low Shutdown Current: <2A Output Adjustable Down to 1.25V Low Profile (1mm) SOT-23 (ThinSOTTM) and (2mm x 3mm x 0.75mm) 6-Pin DFN Packages
APPLICATIONS
n n n n n
Automotive Battery Regulation Industrial Control Supplies Wall Transformer Regulation Distributed Supply Regulation Battery-Powered Equipment
TYPICAL APPLICATION
3.3V Step-Down Converter
95 VIN 4.5V TO 36V 1N4148 VIN BOOST LT1933 OFF ON SHDN GND SW FB 16.5k 2.2F 10k MBRM140 0.1F 22H 90 VOUT 3.3V/500mA EFFICIENCY (%) 85 VOUT = 3.3V 80 75 70
1933 TA01a
Efficiency
VIN = 12V VOUT = 5V
22F
65 0 100 200 300 400 LOAD CURRENT (mA) 500 600
1933 TA01b
1933fd
1
LT1933 ABSOLUTE MAXIMUM RATINGS
(Note 1)
Input Voltage (VIN) .....................................- 0.4V to 36V BOOST Pin Voltage ..................................................43V BOOST Pin Above SW Pin.........................................20V SHDN Pin ................................................... -0.4V to 36V FB Voltage .................................................... -0.4V to 6V Operating Temperature Range (Note 2) LT1933E .................................................. -40C to 85C
LT1933I ................................................. -40C to 125C LT1933H................................................. -40C to 150C Maximum Junction Temperature LT1933E, LT1933I ................................................ 125C LT1933H................................................................ 150C Storage Temperature Range................... -65C to 150C Lead Temperature, S6 Package (Soldering, 10 sec) ........................................... 300C
PIN CONFIGURATION
TOP VIEW TOP VIEW BOOST 1 VIN 2 SW 3 7 6 FB 5 GND 4 SHDN BOOST 1 GND 2 FB 3 6 SW 5 VIN 4 SHDN
DCB PACKAGE 6-LEAD (2mm x 3mm) PLASTIC DFN JA = 73.5C/W, JC = 12C/W EXPOSED PAD (PIN 7) IS GND, MUST BE SOLDERED TO PCB
S6 PACKAGE 6-LEAD PLASTIC TSOT-23 JA = 165C/W, JC = 102C/W
ORDER INFORMATION
LEAD FREE FINISH LT1933IDCB#PBF LT1933HDCB#PBF LT1933ES6#PBF LT1933IS6#PBF LT1933HS6#PBF LEAD BASED FINISH LT1933IDCB LT1933HDCB LT1933ES6 LT1933IS6 LT1933HS6 TAPE AND REEL LT1933IDCB#TRPBF LT1933HDCB#TRPBF LT1933ES6#TRPBF LT1933IS6#TRPBF LT1933HS6#TRPBF TAPE AND REEL LT1933IDCB#TR LT1933HDCB#TR LT1933ES6#TR LT1933IS6#TR LT1933HS6#TR PART MARKING LCGM LCGN LTAGN LTAGP LTDDQ PART MARKING LCGM LCGN LTAGN LTAGP LTDDQ PACKAGE DESCRIPTION 6-Lead (2mm x 3mm) Plastic DFN 6-Lead (2mm x 3mm) Plastic DFN 6-Lead Plastic TSOT-23 6-Lead Plastic TSOT-23 6-Lead Plastic TSOT-23 PACKAGE DESCRIPTION 6-Lead (2mm x 3mm) Plastic DFN 6-Lead (2mm x 3mm) Plastic DFN 6-Lead Plastic TSOT-23 6-Lead Plastic TSOT-23 6-Lead Plastic TSOT-23 TEMPERATURE RANGE -40C to 125C -40C to 150C -40C to 85C -40C to 125C -40C to 150C TEMPERATURE RANGE -40C to 125C -40C to 150C -40C to 85C -40C to 125C -40C to 150C
Consult LTC Marketing for parts specified with wider operating temperature ranges. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
1933fd
2
LT1933 ELECTRICAL CHARACTERISTICS
PARAMETER Undervoltage Lockout Feedback Voltage FB Pin Bias Current Quiescent Current Quiescent Current in Shutdown Reference Line Regulation Switching Frequency Maximum Duty Cycle Switch Current Limit Switch VCESAT Switch Leakage Current Minimum Boost Voltage Above Switch BOOST Pin Current SHDN Input Voltage High SHDN Input Voltage Low SHDN Bias Current VSHDN = 2.3V (Note 5) VSHDN = 0V 34 0.01 ISW = 400mA ISW = 400mA 2.3 0.3 50 0.1 1.9 18 (Note 3) ISW = 400mA, S6 Package ISW = 400mA, DCB6 Package VFB = Measured VREF + 10mV (Note 4) Not Switching VSHDN = 0V VIN = 5V to 36V VFB = 1.1V VFB = 0V
l l l
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 12V, VBOOST = 17V, unless otherwise noted. (Note 2)
CONDITIONS MIN 1.225 TYP 3.35 1.245 40 1.6 0.01 0.01 400 88 0.75 500 55 94 1.05 370 370 500 2 2.3 25 600 MAX 3.6 1.265 120 2.5 2 UNITS V V nA mA A %/V kHz kHz % A mV mV A V mA V V A A
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LT1933E is guaranteed to meet performance specifications from 0C to 70C. Specifications over the -40C to 85C operating temperature range are assured by design, characterization and correlation with statistical process controls. The LT1933I specifications are
guaranteed over the -40C to 125C temperature range. The LT1933H specifications are guaranteed over the -40C to 150C temperature range. Note 3: Current limit guaranteed by design and/or correlation to static test. Slope compensation reduces current limit at higher duty cycle. Note 4: Current flows out of pin. Note 5: Current flows into pin.
1933fd
3
LT1933 TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency, VOUT = 5V
100 TA = 25C VOUT = 5V VIN = 12V EFFICIENCY (%) 100
Efficiency, VOUT = 3.3V
TA = 25C VOUT = 3.3V VIN = 5V VIN = 12V VIN = 24V 70 SWITCH CURRENT LIMIT (mA) 1200 1000 800 600 400 200 0
Switch Current Limit
TA = 25C TYPICAL
90 EFFICIENCY (%)
90
MINIMUM
80
VIN = 24V
80
70 D1 = MBRM140 L1 = Toko D53LCB 33H 0 100 300 400 LOAD CURRENT (mA) 200 500 600
1933 G01
60
60 0 100 200
D1 = MBRM140 L1 = Toko D53LCB 22H 300 400 LOAD CURRENT (mA) 500 600
1933 G02
0
20
60 40 DUTY CYCLE (%)
80
100
1933 G03
Maximum Load Current
800 TA = 25C VOUT = 5V LOAD CURRENT (mA) 800
Maximum Load Current
TA = 25C VOUT = 3.3V SWITCH VOLTAGE (mV) 600 500
Switch Voltage Drop
LOAD CURRENT (mA)
700 L = 33H 600 L = 22H 500
700 L = 22H 600 L = 15H 500
TA = 25C
400 TA = 85C 300 200 100 TA = -40C
400
400 0 5 15 20 10 INPUT VOLTAGE (V) 25 30
1933 G04
0
5
15 20 10 INPUT VOLTAGE (V)
25
30
1933 G05
0
0
0.1
0.3 0.2 0.4 SWITCH CURRENT (A)
0.5
0.6
1933 G06
Feedback Voltage
1.260 1.255 FEEDBACK VOLTAGE (V) 3.6 1.250 UVLO (V) 1.245 1.240 3.2 1.235 1.230 -50 -25 3.4 3.8
Undervoltage Lockout
600 SWITCHING FREQUENCY (kHz)
Switching Frequency
550
500
450
0
25 50 75 100 125 150 TEMPERATURE (C)
1933 G07
3.0 -50 -25
0
25 50 75 100 125 150 TEMPERATURE (C)
1933 G08
400 -50 -25
0
25 50 75 100 125 150 TEMPERATURE (C)
1933 G09
1933fd
4
LT1933 TYPICAL PERFORMANCE CHARACTERISTICS
Frequency Foldback
700 SWITCHING FREQUENCY (kHz) 600 SWITCH CURRENT LIMIT (A) 500 400 300 200 100 0 0.0 1.0 0.5 FB PIN VOLTAGE (V) 1.5
1933 G10
Soft-Start
1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0 2 3 1 SHDN PIN VOLTAGE (V) 4
1933 G11
SHDN Pin Current
200 TA = 25C
TA = 25C
TA = 25C DC = 30% SHDN PIN CURRENT (A)
150
100
50
0 0 8 12 4 SHDN PIN VOLTAGE (V) 16
1933 G12
Typical Minimum Input Voltage
8 VOUT = 5V TA = 25C L = 33H INPUT VOLTAGE (V) TO START 6.0 5.5
Typical Minimum Input Voltage
VOUT = 3.3V TA = 25C L = 22H TO START 5.0 4.5 4.0 3.5 TO RUN 1.4 1.2 SWITCH CURRENT LIMIT (A) 1.0 0.8 0.6 0.4 0.2
Switch Current Limit
7 INPUT VOLTAGE (V)
6
TO RUN 5
4 1 10 100 LOAD CURRENT (mA)
1933 G13
3.0 1 10 100 LOAD CURRENT (mA)
1933 G14
0 -50 -25
0
25 50 75 100 125 150 TEMPERATURE (C)
1933 G15
Operating Waveforms
VOUT1 1.8V
Operating Waveforms, Discontinuous Mode
VOUT1 1.8V
VSW 10V/DIV
VSW 10V/DIV
IL 200mA/DIV
VOUT2 1.2V
IL 200mA/DIV
VOUT2 1.2V
VOUT 10mV/DIV
1933 G16
VOUT 10mV/DIV
1933 G17
VIN = 12V, VOUT = 3.3V, IOUT = 400mA, L = 22H, COUT = 22F
VIN = 12V, VOUT = 3.3V, IOUT = 20mA, L = 22H, COUT = 22F
1933fd
5
LT1933 PIN FUNCTIONS
(SOT-23/DFN)
BOOST (Pin 1): The BOOST pin is used to provide a drive voltage, higher than the input voltage, to the internal bipolar NPN power switch. GND (Pin 2/Pin 5 and Exposed Pad, Pin 7): Tie the GND pin to a local ground plane below the LT1933 and the circuit components. Return the feedback divider to this pin. FB (Pin 3/Pin 6): The LT1933 regulates its feedback pin to 1.245V. Connect the feedback resistor divider tap to this pin. Set the output voltage according to VOUT = 1.245V (1 + R1/R2). A good value for R2 is 10k.
SHDN (Pin 4): The SHDN pin is used to put the LT1933 in shutdown mode. Tie to ground to shut down the LT1933. Tie to 2.3V or more for normal operation. If the shutdown feature is not used, tie this pin to the VIN pin. SHDN also provides a soft-start function; see the Applications Information section. VIN (Pin 5/Pin 2): The VIN pin supplies current to the LT1933's internal regulator and to the internal power switch. This pin must be locally bypassed. SW (Pin 6): The SW pin is the output of the internal power switch. Connect this pin to the inductor, catch diode and boost capacitor.
BLOCK DIAGRAM
VIN C2 INT REG AND UVLO VIN
ON OFF R3 SHDN
SLOPE COMP
R S Q Q
BOOST
D2
C3 DRIVER Q1 SW D1 L1 VOUT C1
C4 OSC FREQUENCY FOLDBACK
VC
gm
1.245V
GND R2
FB R1
1933 BD
1933fd
6
LT1933 OPERATION
(Refer to Block Diagram)
The LT1933 is a constant frequency, current mode step down regulator. A 500kHz oscillator enables an RS flipflop, turning on the internal 750mA power switch Q1. An amplifier and comparator monitor the current flowing between the VIN and SW pins, turning the switch off when this current reaches a level determined by the voltage at VC. An error amplifier measures the output voltage through an external resistor divider tied to the FB pin and servos the VC node. If the error amplifier's output increases, more current is delivered to the output; if it decreases, less current is delivered. An active clamp (not shown) on the VC node provides current limit. The VC node is also clamped to the voltage on the SHDN pin; soft-start is implemented by generating a voltage ramp at the SHDN pin using an external resistor and capacitor.
An internal regulator provides power to the control circuitry. This regulator includes an undervoltage lockout to prevent switching when VIN is less than ~3.35V. The SHDN pin is used to place the LT1933 in shutdown, disconnecting the output and reducing the input current to less than 2A. The switch driver operates from either the input or from the BOOST pin. An external capacitor and diode are used to generate a voltage at the BOOST pin that is higher than the input supply. This allows the driver to fully saturate the internal bipolar NPN power switch for efficient operation. The oscillator reduces the LT1933's operating frequency when the voltage at the FB pin is low. This frequency foldback helps to control the output current during startup and overload.
APPLICATIONS INFORMATION
FB Resistor Network The output voltage is programmed with a resistor divider between the output and the FB pin. Choose the 1% resistors according to: R1 = R2(VOUT/1.245 - 1) R2 should be 20k or less to avoid bias current errors. Reference designators refer to the Block Diagram. Input Voltage Range The input voltage range for LT1933 applications depends on the output voltage and on the absolute maximum ratings of the VIN and BOOST pins. The minimum input voltage is determined by either the LT1933's minimum operating voltage of ~3.35V, or by its maximum duty cycle. The duty cycle is the fraction of time that the internal switch is on and is determined by the input and output voltages: DC = (VOUT + VD)/(VIN - VSW + VD) where VD is the forward voltage drop of the catch diode (~0.4V) and VSW is the voltage drop of the internal switch (~0.4V at maximum load). This leads to a minimum input voltage of: VIN(MIN) = (VOUT + VD)/DCMAX - VD + VSW with DCMAX = 0.88 The maximum input voltage is determined by the absolute maximum ratings of the VIN and BOOST pins and by the minimum duty cycle DCMIN = 0.08 (corresponding to a minimum on time of 130ns): VIN(MAX) = (VOUT + VD)/DCMIN - VD + VSW Note that this is a restriction on the operating input voltage; the circuit will tolerate transient inputs up to the absolute maximum ratings of the VIN and BOOST pins. Inductor Selection and Maximum Output Current A good first choice for the inductor value is: L = 5 (VOUT + VD) where VD is the voltage drop of the catch diode (~0.4V) and L is in H. With this value the maximum load current will be above 500mA. The inductor's RMS current rating must be greater than your maximum load current and its
1933fd
7
LT1933 APPLICATIONS INFORMATION
saturation current should be about 30% higher. For robust operation in fault conditions the saturation current should be ~1A. To keep efficiency high, the series resistance (DCR) should be less than 0.2. Table 1 lists several vendors and types that are suitable. Of course, such a simple design guide will not always result in the optimum inductor for your application. A larger value provides a slightly higher maximum load current, and will reduce the output voltage ripple. If your load is lower than 500mA, then you can decrease the value of the inductor and operate with higher ripple current. This allows you to use a physically smaller inductor, or one with a lower DCR resulting in higher efficiency. There are several graphs in the Typical Performance Characteristics section of this data sheet that show the maximum load current as a function of input voltage and inductor value for several popular output voltages. Low inductance may result in discontinuous mode operation, which is OK, but further reduces maximum load current. For details of maximum output current and discontinuous mode operation, see Linear Technology Application Note 44. Finally, for duty cycles greater than 50% (VOUT/VIN > 0.5), there is a minimum inductance required to avoid subharmonic oscillations. Choosing L greater than 3(VOUT + VD) H prevents subharmonic oscillations at all duty cycles. Catch Diode A 0.5A or 1A Schottky diode is recommended for the catch diode, D1. The diode must have a reverse voltage rating equal to or greater than the maximum input voltage. The ON Semiconductor MBR0540 is a good choice; it is rated for 0.5A forward current and a maximum reverse voltage of 40V. The MBRM140 provides better efficiency, and will handle extended overload conditions. Input Capacitor Bypass the input of the LT1933 circuit with a 2.2F or higher value ceramic capacitor of X7R or X5R type. Y5V types have poor performance over temperature and applied voltage, and should not be used. A 2.2F ceramic is adequate to bypass the LT1933 and will easily handle the ripple current. However, if the input power source has high impedance, or there is significant inductance due to long wires or cables, additional bulk capacitance may be necessary. This can be provided with a low performance electrolytic capacitor. Step-down regulators draw current from the input supply in pulses with very fast rise and fall times. The input capacitor is required to reduce the resulting voltage ripple at the LT1933 and to force this very high frequency
Table 1.Inductor Vendors
Vendor Coilcraft URL www.coilcraft.com Part Series D01608C MSS5131 MSS6122 Sumida www.sumida.com CR43 CDRH4D28 CDRH5D28 Toko Wurth Elektronik www.toko.com www.we-online.com D52LC D53LC WE-TPC MH WE-PD4 S WE-PD2 S Inductance Range (H) 10 to 22 10 to 22 10 to 33 10 to 22 10 to 33 22 to 47 10 to 22 22 to 47 10 to 22 10 to 22 10 to 47 Size (mm) 2.9 x 4.5 x 6.6 3.1 x 5.1 x 5.1 2.2 x 6.1 x 6.1 3.5 x 4.3 x 4.8 3.0 x 5.0 x 5.0 3.0 x 5.7 x 5.7 2.0 x 5.0 x 5.0 3.0 x 5.0 x 5.0 2.8 x 4.8 x 4.8 2.9 x 4.5 x 6.6 3.2 x 4.0 x 4.5
1933fd
8
LT1933 APPLICATIONS INFORMATION
switching current into a tight local loop, minimizing EMI. A 2.2F capacitor is capable of this task, but only if it is placed close to the LT1933 and the catch diode; see the PCB Layout section. A second precaution regarding the ceramic input capacitor concerns the maximum input voltage rating of the LT1933. A ceramic input capacitor combined with trace or cable inductance forms a high quality (under damped) tank circuit. If the LT1933 circuit is plugged into a live supply, the input voltage can ring to twice its nominal value, possibly exceeding the LT1933's voltage rating. This situation is easily avoided; see the Hot Plugging Safely section. Output Capacitor The output capacitor has two essential functions. Along with the inductor, it filters the square wave generated by the LT1933 to produce the DC output. In this role it determines the output ripple, and low impedance at the switching frequency is important. The second function is to store energy in order to satisfy transient loads and stabilize the LT1933's control loop. Ceramic capacitors have very low equivalent series resistance (ESR) and provide the best ripple performance. A good value is COUT = 60/VOUT where COUT is in F Use X5R or X7R types, and keep . in mind that a ceramic capacitor biased with VOUT will have less than its nominal capacitance. This choice will provide low output ripple and good transient response. Transient performance can be improved with a high value capacitor, but a phase lead capacitor across the feedback resistor R1 may be required to get the full benefit (see the Compensation section). High performance electrolytic capacitors can be used for the output capacitor. Low ESR is important, so choose one that is intended for use in switching regulators. The ESR should be specified by the supplier, and should be 0.1 or less. Such a capacitor will be larger than a ceramic capacitor and will have a larger capacitance, because the capacitor must be large to achieve low ESR. Table 2 lists several capacitor vendors.
Table 2.Inductor Vendors
Vendor Panasonic Phone (714) 373-7366 URL www.panasonic.com Part Series Ceramic, Polymer, Tantalum Ceramic, Tantalum Ceramic, Polymer, Tantalum Ceramic Ceramic, Tantalum Ceramic TPS Series Comments EEF Series
Kemet Sanyo
(864) 963-6300 (408) 749-9714
www.kemet.com www.sanyovideo.com
T494, T495 POSCAP
Murata AVX Taiyo Yuden
(404)436-1300
www.murata.com www.avxcorp.com
(864)963-6300
www.taiyo-yuden.com
1933fd
9
LT1933 APPLICATIONS INFORMATION
Figure 1 shows the transient response of the LT1933 with several output capacitor choices. The output is 3.3V. The load current is stepped from 100mA to 400mA and back to 100mA, and the oscilloscope traces show the output voltage. The upper photo shows the recommended value. The second photo shows the improved response (less voltage drop) resulting from a larger output capacitor and a phase lead capacitor. The last photo shows the response to a high performance electrolytic capacitor. Transient performance is improved due to the large output capacitance, but output ripple (as shown by the broad trace) has increased because of the higher ESR of this capacitor.
VOUT 16.5k FB 10k 22F
VOUT 50mV/DIV
IOUT 200mA/DIV
1933 F01a
VOUT 16.5k FB 10k 470pF 22F 2x
VOUT 50mV/DIV
IOUT 200mA/DIV
1933 F01b
VOUT 16.5k
VOUT 50mV/DIV
+
FB 10k 100F SANYO 4TPB100M
1933 F01c
IOUT 200mA/DIV
Figure 1. Transient Load Response of the LT1933 with Different Output Capacitors as the Load Current is Stepped from 100mA to 400mA. VIN = 12V, VOUT = 3.3V, L = 22H.
1933fd
10
LT1933 APPLICATIONS INFORMATION
BOOST Pin Considerations Capacitor C3 and diode D2 are used to generate a boost voltage that is higher than the input voltage. In most cases a 0.1F capacitor and fast switching diode (such as the 1N4148 or 1N914) will work well. Figure 2 shows two ways to arrange the boost circuit. The BOOST pin must be at least 2.3V above the SW pin for best efficiency. For outputs of 3V and above, the standard circuit (Figure 2a) is best. For outputs between 2.5V and 3V, use a 0.47F capacitor and a small Schottky diode (such as the BAT-54). For lower output voltages the boost diode can be tied to the input (Figure 2b). The circuit in Figure 2a is more efficient because the BOOST pin current comes from a lower voltage source. You must also be sure that the maximum voltage rating of the BOOST pin is not exceeded.
D2
The minimum operating voltage of an LT1933 application is limited by the undervoltage lockout (~3.35V) and by the maximum duty cycle as outlined above. For proper startup, the minimum input voltage is also limited by the boost circuit. If the input voltage is ramped slowly, or the LT1933 is turned on with its SHDN pin when the output is already in regulation, then the boost capacitor may not be fully charged. Because the boost capacitor is charged with the energy stored in the inductor, the circuit will rely on some minimum load current to get the boost circuit running properly. This minimum load will depend on input and output voltages, and on the arrangement of the boost circuit. The minimum load generally goes to zero once the circuit has started. Figure 3 shows a plot of minimum load to start and to run as a function of input voltage. In many
D2 C3 SW GND VOUT
BOOST LT1933 VIN VIN GND VBOOST - VSW VOUT MAX VBOOST VIN + VOUT (2a) SW
C3 VOUT VIN VIN
BOOST LT1933
1933 F02a
VBOOST - VSW VIN MAX VBOOST 2VIN (2b)
1933 F02b
Figure 2. Two Circuits for Generating the Boost Voltage
Minimum Input Voltage VOUT = 3.3V
6.0 5.5 TO START INPUT VOLTAGE (V) 5.0 4.5 4.0 3.5 3.0 1 10 100 LOAD CURRENT (mA)
1933 F03a
Minimum Input Voltage VOUT = 5V
6.0 5.5 TO START INPUT VOLTAGE (V) 5.0 4.5 4.0 3.5 3.0 1 10 100 LOAD CURRENT (mA)
1933 F03b
VOUT = 3.3V TA = 25C L = 22H
VOUT = 5V TA = 25C L = 22H
TO RUN
TO RUN
Figure 3. The Minimum Input Voltage Depends on Output Voltage, Load Current and Boost Circuit
1933fd
11
LT1933 APPLICATIONS INFORMATION
cases the discharged output capacitor will present a load to the switcher which will allow it to start. The plots show the worst-case situation where VIN is ramping very slowly. For lower start-up voltage, the boost diode can be tied to VIN; however, this restricts the input range to one-half of the absolute maximum rating of the BOOST pin. At light loads, the inductor current becomes discontinuous and the effective duty cycle can be very high. This reduces the minimum input voltage to approximately 300mV above VOUT. At higher load currents, the inductor current is continuous and the duty cycle is limited by the maximum duty cycle of the LT1933, requiring a higher input voltage to maintain regulation. Soft-Start The SHDN pin can be used to soft-start the LT1933, reducing the maximum input current during start up. The SHDN pin is driven through an external RC filter to create a voltage ramp at this pin. Figure 4 shows the start up waveforms with and without the soft-start circuit. By choosing a large RC time constant, the peak start up current can be reduced to the current that is required to regulate the output, with no overshoot. Choose the value of the resistor so that it can supply 60A when the SHDN pin reaches 2.3V.
RUN 5V/DIV RUN SHDN GND IIN 100mA/DIV VOUT 5V/DIV 50s/DIV
1933 F04a
RUN 15k SHDN 0.1F GND
RUN 5V/DIV
1933 F04b
IIN 100mA/DIV VOUT 5V/DIV 0.5ms/DIV
Figure 4. To Soft-Start the LT1933, Add a Resistor and Capacitor to the SHDN Pin. VINI = 12V, VOUT = 3.3V, COUT = 22F RLOAD = 10 ,
1933fd
12
LT1933 APPLICATIONS INFORMATION
Shorted and Reversed Input Protection If the inductor is chosen so that it won't saturate excessively, an LT1933 buck regulator will tolerate a shorted output. There is another situation to consider in systems where the output will be held high when the input to the LT1933 is absent. This may occur in battery charging applications or in battery backup systems where a battery or some other supply is diode OR-ed with the LT1933's output. If the VIN pin is allowed to float and the SHDN pin is held high (either by a logic signal or because it is tied to VIN), then the LT1933's internal circuitry will pull its quiescent current through its SW pin. This is fine if your system can tolerate a few mA in this state. If you ground the SHDN pin, the SW pin current will drop to essentially zero. However, if the VIN pin is grounded while the output is held high, then parasitic diodes inside the LT1933 can pull large currents from the output through the SW pin and the VIN pin. Figure 5 shows a circuit that will run only when the input voltage is present and that protects against a shorted or reversed input. Hot Plugging Safely The small size, robustness and low impedance of ceramic capacitors make them an attractive option for the input bypass capacitor of LT1933 circuits. However, these capacitors can cause problems if the LT1933 is plugged into a live supply (see Linear Technology Application Note 88 for a complete discussion). The low loss ceramic capacitor combined with stray inductance in series with the power source forms an under damped tank circuit, and the voltage at the VIN pin of the LT1933 can ring to twice the nominal input voltage, possibly exceeding the LT1933's rating and damaging the part. If the input supply is poorly controlled or the user will be plugging the LT1933 into an energized supply, the input network should be designed to prevent this overshoot.
D4 VIN VIN BOOST LT1933 SHDN GND SW FB VOUT
BACKUP
1933 F05
D4: MBR0540
Figure 5. Diode D4 Prevents a Shorted Input from Discharging a Backup Battery Tied to the Output; It Also Protects the Circuit from a Reversed Input. The LT1933 Rns Only When the Input is Present
1933fd
13
LT1933 APPLICATIONS INFORMATION
CLOSING SWITCH SIMULATES HOT PLUG IIN VIN LT1933
DANGER! VIN 20V/DIV RINGING VIN MAY EXCEED ABSOLUTE MAXIMUM RATING OF THE LT1933
+
2.2F
LOW IMPEDANCE ENERGIZED 24V SUPPLY
STRAY INDUCTANCE DUE TO 6 FEET (2 METERS) OF TWISTED PAIR
IIN 5A/DIV 20s/DIV
(6a)
LT1933
+
10F 35V AI.EI.
+
2.2F
VIN 20V/DIV
IIN 5A/DIV 20s/DIV
(6b)
1 LT1933
+
0.1F 2.2F
VIN 20V/DIV
IIN 5A/DIV 20s/DIV
1933 F06
(6c) Figure 6. A Well Chosen Input Network Prevents Input Voltage Overshoot and Ensures Reliable Operation When the LT1933 is Connected to a Live Supply
1933fd
14
LT1933 APPLICATIONS INFORMATION
Figure 6 shows the waveforms that result when an LT1933 circuit is connected to a 24V supply through six feet of 24-gauge twisted pair. The first plot is the response with a 2.2F ceramic capacitor at the input. The input voltage rings as high as 35V and the input current peaks at 20A. One method of damping the tank circuit is to add another capacitor with a series resistor to the circuit. In Figure 6b an aluminum electrolytic capacitor has been added. This capacitor's high equivalent series resistance damps the circuit and eliminates the voltage overshoot. The extra capacitor improves low frequency ripple filtering and can slightly improve the efficiency of the circuit, though it is likely to be the largest component in the circuit. An alternative solution is shown in Figure 6c. A 1 resistor is added in series with the input to eliminate the voltage overshoot (it also reduces the peak input current). A 0.1F capacitor improves high frequency filtering. This solution is smaller and less expensive than the electrolytic capacitor. For high input voltages its impact on efficiency is minor, reducing efficiency less than one half percent for a 5V output at full load operating from 24V. Frequency Compensation The LT1933 uses current mode control to regulate the output. This simplifies loop compensation. In particular, the LT1933 does not require the ESR of the output capacitor for stability allowing the use of ceramic capacitors to achieve low output ripple and small circuit size.
LT1933 0.7V
Figure 7 shows an equivalent circuit for the LT1933 control loop. The error amp is a transconductance amplifier with finite output impedance. The power section, consisting of the modulator, power switch and inductor, is modeled as a transconductance amplifier generating an output current proportional to the voltage at the VC node. Note that the output capacitor integrates this current, and that the capacitor on the VC node (CC) integrates the error amplifier output current, resulting in two poles in the loop. RC provides a zero. With the recommended output capacitor, the loop crossover occurs above the RCCC zero. This simple model works well as long as the value of the inductor is not too high and the loop crossover frequency is much lower than the switching frequency. With a larger ceramic capacitor (very low ESR), crossover may be lower and a phase lead capacitor (CPL) across the feedback divider may improve the phase margin and transient response. Large electrolytic capacitors may have an ESR large enough to create an additional zero, and the phase lead may not be necessary. If the output capacitor is different than the recommended capacitor, stability should be checked across all operating conditions, including load current, input voltage and temperature. The LT1375 data sheet contains a more thorough discussion of loop compensation and describes how to test the stability using a transient load.
gm 1.1mho VC RC 100k CC 80pF GND
CURRENT MODE POWER STAGE SW R1 FB ESR CPL
gm = 150mhos ERROR AMPLIFIER 500k
Figure 7. Model for Loop Response
1933fd
-
+
- +
OUT
1.245V
+
C1 R2
C1
1933 F07
15
LT1933 APPLICATIONS INFORMATION
PCB Layout For proper operation and minimum EMI, care must be taken during printed circuit board layout. Figure 8 shows the recommended component placement with trace, ground plane and via locations. Note that large, switched currents flow in the LT1933's VIN and SW pins, the catch diode (D1) and the input capacitor (C2). The loop formed by these components should be as small as possible and tied to system ground in only one place. These components, along with the inductor and output capacitor, should be placed on the same side of the circuit board, and their connections should be made on that layer. Place a local, unbroken ground plane below these components, and tie this ground plane to system ground at one location, ideally at the ground terminal of the output capacitor C1. The SW and BOOST nodes should be as small as possible. Finally, keep the FB node small so that the ground pin and ground traces will shield it from the SW and BOOST nodes. Include two vias near the GND pin of the LT1933 to help remove heat from the LT1933 to the ground plane. Figure 8a shows the layout for the DFN package. Vias near and under the exposed die attach paddle minimize the thermal resistance of the LT1933.
VOUT
VIN
C1
D1
C2
GND
VIAS
1933 F08a
(8a) DFN Package
SHUTDOWN VIN C1 C2 D1 VOUT SYSTEM GROUND
VIAS OUTLINE OF LOCAL GROUND PLANE
1933 F08b
(8b) SOT-23 Package Figure 8. A Good PCB Layout Ensures Proper, Low EMI Operation
1933fd
16
LT1933 TYPICAL APPLICATIONS
3.3V Step-Down Converter
VIN 4.5V TO 36V OFF ON D2 VIN BOOST LT1933 SHDN GND SW FB R1 16.5k R2 10k D1 C1 22F 6.3V
1933 TA02b
C3 0.1F
L1 22H
VOUT 3.3V/ 500mA
C2 2.2F
12V Step-Down Converter
VIN 14.5V TO 36V OFF ON D3, 6V VIN BOOST LT1933 SHDN GND SW FB R1 86.6k R2 10k D1 C1 10F
1933 TA02d
D2 L1 47H
C3 0.1F
VOUT 12V/ 450mA
C2 2.2F
1933fd
17
LT1933 PACKAGE DESCRIPTION
DCB Package 6-Lead Plastic DFN (2mm x 3mm)
(Reference LTC DWG # 05-08-1715)
0.70 0.05
3.55 0.05
1.65 0.05 (2 SIDES) PACKAGE OUTLINE
2.15 0.05
0.25 0.05 0.50 BSC 1.35 0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 2.00 0.10 (2 SIDES) R = 0.115 TYP 4 6 0.40 0.10
R = 0.05 TYP
3.00 0.10 (2 SIDES) PIN 1 BAR TOP MARK (SEE NOTE 6)
1.65 0.10 (2 SIDES) PIN 1 NOTCH R0.20 OR 0.25 x 45 CHAMFER 3 1
(DCB6) DFN 0405
0.200 REF
0.75 0.05
0.25 0.05 0.50 BSC 1.35 0.10 (2 SIDES)
0.00 - 0.05
BOTTOM VIEW--EXPOSED PAD
NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (TBD) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE
1933fd
18
LT1933 PACKAGE DESCRIPTION
S6 Package 6-Lead Plastic SOT-23
(Reference LTC DWG # 05-08-1634)
0.62 MAX
0.95 REF
2.80 - 3.10 (NOTE 4)
1.22 REF
3.85 MAX 2.62 REF
1.4 MIN
2.60 - 3.00 1.50 - 1.75 (NOTE 4) PIN ONE ID
RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR
0.95 BSC
0.25 - 0.50 TYP 6 PLCS NOTE 3
0.90 - 1.30 0.20 BSC 0.90 - 1.45 DATUM `A'
0.35 - 0.55 REF
NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING 4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6. PACKAGE EIAJ REFERENCE IS SC-74A (EIAJ)
0.09 - 0.20 (NOTE 3)
1.90 BSC
0.09 - 0.15 NOTE 3
S6 SOT-23 0502
ATTENTION: ORIGINAL SOT23-6L PACKAGE. MOST SOT23-6L PRODUCTS CONVERTED TO THIN SOT23 PACKAGE, DRAWING # 05-08-1636 AFTER APPROXIMATELY APRIL 2001 SHIP DATE
1933fd
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
19
LT1933 TYPICAL APPLICATION
2.5V Step-Down Converter
D2 VIN 3.6V TO 36V VIN BOOST LT1933 OFF ON SHDN GND SW FB R1 10.5k R2 10k D1 C1 22F
1933 TA03
C3 L1 0.47F 15H
VOUT 2.5V/500mA
C2 2.2F
RELATED PARTS
PART NUMBER LT1074/LT1074HV LT1076/LT1076HV LT1676 LT1765 LT1766 LT1767 LT1776 LT1940 LT1956 LT1976 LT3010 LT3407 LT3412 LTC3414 LT3430/LT3431 DESCRIPTION 4.4A IOUT, 100kHz, High Efficiency Step-Down DC/DC Converter 1.6A IOUT, 100kHz, High Efficiency Step-Down DC/DC Converter 60V, 440mA IOUT, 100kHz, High Efficiency Step-Down DC/DC Converter 25V, 2.75mA IOUT, 1.25MHz, High Efficiency Step-Down DC/DC Converter COMMENTS VIN: 7.3V to 45V/64V, VOUT(MIN) = 2.21V, IQ = 8.5mA, ISD = 10A, DD-5/DD-7, TO220-5/TO220-7 Packages VIN: 7.3V to 45V/64V, VOUT(MIN) = 2.21V, IQ = 8.5mA, ISD = 10A, DD-5/DD-7, TO220-5/TO220-7 Packages VIN: 7.4V to 60V, VOUT(MIN) = 1.24V, IQ = 3.2mA, ISD = 2.5A, S8 Package VIN: 3V to 25V, VOUT(MIN) = 1.2V, IQ = 1mA, ISD = 15A, S8, TSSOP16E Packages
60V, 1.2A IOUT, 200kHz, High Efficiency Step-Down DC/DC VIN: 5.5V to 60V, VOUT(MIN) = 1.2V, IQ = 2.5mA, ISD = 25A, Converter S8, TSSOP16/TSSOP16E Packages 25V, 1.2A IOUT, 1.25MHz, High Efficiency Step-Down DC/DC Converter 40V, 550mA IOUT, 200kHz, High Efficiency Step-Down DC/DC Converter 25V, Dual 1.4A IOUT, 1.1MHz, High Efficiency Step-Down DC/DC Converter 60V, Dual 1.2A IOUT, 500kHz, High Efficiency Step-Down DC/DC Converter 60V, Dual 1.2A IOUT, 200kHz, High Efficiency Step-Down DC/DC Converter with Burst Mode(R) 80V, 50mA, Low Noise Linear Regulator Dual 600mA IOUT, 1.5MHz, Synchronous Step-Down DC/DC Converter 2.5A IOUT, 4MHz, Synchronous Step-Down DC/DC Converter VIN: 3V to 25V, VOUT(MIN) = 1.2V, IQ = 1mA, ISD = 6A, S8, MS8/MS8E Packages VIN: 7.4V to 40V, VOUT(MIN) = 1.24V, IQ = 3.2mA, ISD = 30A, S8, N8, S8 Packages VIN: 3.6V to 25V, VOUT(MIN) = 1.25V, IQ = 3.8mA, ISD = <30A, TSSOP16E Package VIN: 5.5V to 60V, VOUT(MIN) = 1.2V, IQ = 2.5mA, ISD = 25A, TSSOP16/TSSOP16E Packages VIN: 3.3V to 60V, VOUT(MIN) = 1.2V, IQ = 100A, ISD = <1A, TSSOP16E Package VIN: 1.5V to 80V, VOUT(MIN) = 1.28V, IQ = 30A, ISD = <1A, MS8E Package VIN: 2.5V to 5.5V, VOUT(MIN) =0.6V, IQ = 40A, ISD = <1A, MS10E Package VIN: 2.5V to 5.5V, VOUT(MIN) =0.8V, IQ = 60A, ISD = <1A, TSSOP16E Package
4A IOUT, 4MHz, Synchronous Step-Down DC/DC Converter VIN: 2.3V to 5.5V, VOUT(MIN) =0.8V, IQ = 64A, ISD = <1A, TSSOP20E Package 60V, 2.75A IOUT, 200kHz/500kHz, Synchronous Step-Down VIN: 5.5V to 60V, VOUT(MIN) =1.2V, IQ = 2.5mA, ISD = 30A, DC/DC Converter TSSOP16E Package
Burst Mode is a registered trademark of Linear Technology Corporation.
1933fd
20 Linear Technology Corporation
(408) 432-1900 FAX: (408) 434-0507
LT 0108 REV D * PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
www.linear.com
(c) LINEAR TECHNOLOGY CORPORATION 2007

▲Up To Search▲

Price & Availability of LT19331

	To Download LT19331 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .